PTO BUILD COMPLETE

CS6 and CS8 Series Power Take-Off

Model Number

CS8SU6807A1KX

Build ID

Use this unique build ID when referencing your order

61824564975790

List Price

$3154.04

Build Breakdown

Manufacturer: EATON/FULLER

Model: FOM-15E310C-LAS


Bolt Type: SAE 8-BOLT OPENING

Rotation: OPP

PTO %: 107%

Torque: 300 lbs.ft.

HP: 57 HP

PTO Series: CS6/CS8 Series

Transmission Gear: U68

Gear Ratio: 07

Shift Type: A - Manual Air

Assembly Arrangement: 1

Output Type: K - SAE "B" 2 or 4 Bolt, 7/8" 13 Spline

Special Feature: X - None


POWER TAKE OFF
  • CS8SU6807A1KX
    PTO Part Number
    $3154.04
  • TOTAL
    $5173.04
FOOTNOTES
MODEL FOOTNOTES
ADAPTER FOOTNOTES
PTO FOOTNOTES
18 ratio TG interferes with adjacent gear.
6
TG Series Input Gear (U68): #03T34284 -- Refer to kit program on pages 10 & 11.
1
RL Series with combined reduction gear box.
5
Do not use for continuous duty applications. (RL Series)
8
TG Series Input Gear (S68): #03T94243 -- Refer to kit program on pages 10 & 11.
2
Optional: TG PTOs with U68 input gear can be replaced by S68 input gear to obtain output speed 92% of speed shown. Add spacer 23M80190 and stud kit 20MK8808.
7
PTO must be wired through the TCM as described by Eaton in their PTO manual TRIG-2600. DM3. type transmissions must operate at engine speed above 10000 RPM. Only the DM3 type transmission must operate at engine speed above 1000 RPM.
11
On RTLO-16913L-DM3, RTLOM-16913L-DM3, FO-16D313E-LEP , and FOM-16D313E-LEP there is an inertia brake mounted to this location and PTOs inertia brake mounted to this location and PTOs inertia brake cannot be moved, use right side opening. VMS,MHP,MXP,VXP version transmissions have an internal inertia brake and this does not obstruct this PTO opening.
10
PTO rating shown is maximum calculated PTO rating which will not exceed the 500 lb. ft. rating set by Eaton for their transmissions with roller bearings. Refer to Eaton bulletin TMIB-127. Maximum PTO torque must not exceed this rating or the PTO rating shown on page 22 of the general information section.
9
Vehicles with set-back front axles and direct mount pumps may find better clearance with a "3" assembly PTO.Transmissions with clutch assist cylinder on bottom of transmission are best with the "1" arrangement PTO.
3
Direct Mount Dump Pump installation is best with "1" arrangement PTO. Proper support bracket is required from rear of pump to transmission.
13
** refers to transmission torque rating code, 10, 14, 15, 16, 18, 20, 22. Does not change PTO application.
12
40TU6886-1 + 23M80500 + 20MK8817. When using the 40TU6886-1 adapter to change rotation -- Change TG Series, CS Series, SH Series, and RL Series to 6-bolt PTO housing (TG6S, CS6S, SH6S, and RL6D respectively). Add 23M60200S + 20MK6603 for RL Series on PTO side of adapter.
4
  • Six transmission input gears: Fits most popular automatic and manual transmissions
  • Three remote mount output shafts in keyed and flange types: Versatility for remote pump drives
  • S.A.E. "A", "B", and "BB"; DIN 5462 direct mount pump options: Fits most popular pumps
  • Rotatable direct mount flanges: Allows pump to be positioned for maximum clearance
  • Patented Muncie drag brake: Prevents shaft rotation in "OFF" mode
  • Optional pulse generator: Lets System Protection Device monitor PTO shaft speed
  • Brochure
    CS6 and CS8 Series Spec Brochure
  • Brochure
    Hino PTO Wiring Harness
  • Installation Instructions
    Aisin Supplemental Instruction
  • Installation Instructions
    CS6 - “S” & “R” Activation Kit Installation Supplement to IN84-03
  • Installation Instructions
    CS6 and CS8 Series Supplement for EatonFuller UltraShift RTO**910BDM2 Transmissions
  • Installation Instructions
    CS6 and SH6 Series Stud Kit Installation
  • Installation Instructions
    CS6B and FA6B for 2013-2024 Ram 6.4L Gas Engine Installation Instructions
  • Installation Instructions
    Electric over Hydraulic Supplemental Instructions for CS PTO
  • Installation Instructions
    Hino PTO Interface 2021and Later for CS6
  • Installation Instructions
    Hino PTO Wiring Installation for Allison 2500
  • Installation Instructions
    Installation and Owners Manual for 6 and 8 bolt PTOs
  • Product Bulletin
    CS6 and CS8 Seal Replacement
  • Product Bulletin
    CS6 and CS8 Series Gear Code Obsolescence
  • Product Bulletin
    CS6B-I84 Installation Kits on RAM Applications
  • Product Bulletin
    Pressure Switch Deviation
  • Service Parts Manual
    CS6 and CS8 Output Shaft Sub Assemblies
  • Service Parts Manual
    CS6 and CS8 Service Parts Manual

The Muncie Power Take-Off is warranted to be free of defects in material or workmanship and to meet Muncie’s standard written specifications at the time of sale. Muncie’s obligation and liability under this warranty is expressly limited to repairing or replacing, at Muncie’s option, within one year after date of original installation any defective part or parts or any product not meeting the specifications.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED. MUNCIE MAKES NO WARRANTY OF MERCHANTABILITY OR OF FITNESS FOR ANY PARTICULAR PURPOSE. MUNCIE’S OBLIGATION UNDER THIS WARRANTY SHALL NOT INCLUDE ANY TRANSPORTATION CHARGES OR COSTS OF INSTALLATION OR ANY LIABILITY FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OR DELAY. THE REMEDIES SET FORTH HEREIN ARE EXCLUSIVE, AND MUNCIE’S LIABILITY WITH RESPECT TO ANY CONTRACT OR SALE OR ANYTHING DONE IN CONNECTION THEREWITH, WHETHER IN CONTRACT, IN TORT, UNDER ANY WARRANTY, OR OTHERWISE, SHALL NOT, EXCEPT AS EXPRESSLY PROVIDED HEREIN, EXCEED THE PRICE OF THE PRODUCT OR PART ON WHICH SUCH LIABILITY IS BASED.

If requested by Muncie, products or parts for which a warranty claim is made are to be returned transportation prepaid to a Muncie Service Center. Any installation or use not in accordance with catalog or package instructions, other improper use, operation beyond capacity, substitution of parts not approved by Muncie, use with equipment other than the equipment on which the Power Take-Off is first installed, or alteration or repair made to the Power Take-Off other than at a Muncie Service Center, shall void this warranty. No employee or representative of Muncie is authorized to change this warranty in any way or to grant any other warranty.

Prices in this program do not constitute an offer to sell. Suggested prices may change without notice. Please contact Muncie Power Products or your local distributor for current pricing on any items listed as $0.00. All prices are in U.S. dollars.

All information included in the M-Power Spec program is complete and correct to the best of our knowledge. However, we cannot assume any responsibility for errors.

© 2021 Muncie Power Products, Inc.